Get Adobe Flash player

SBA

Swimming pool dehumidifiers

Series SBA dehumidifier are expressly designed for use in swimming pools where humidity should be closely controlled in order to guarantee optimal comfort. This series comprises five models which cover a capacity range from 50 to 200 l/24h.

SBA units are designed for easy maintenance and service, each part being rea dily accessible and, when required, easily replaceable thus reducing service and maintenance costs.

SDH

Swimming pool dehumidifiers

Series SDH dehumidifier are expressly designed for use in swimming pools where humidity should be closely controlled in order to guarantee optimal comfort. These units are intended to be installed in a technical room close to the swimming pool. A centrifugal fan with high available static pressure allows unit connection to duct-works, both for air suction and discharge.

This series comprises 2 basic models which cover a capacity range from 94 to 124 l/24h.

SEH

Swimming pool dehumidifiers

Series SEH dehumidifier are expressly designed for use in swimming pools where humidity should be closely controlled in order to guarantee optimal comfort. These units are intended to be installed in a technical room close to the swimming pool. A centrifugal fan with high available static pressure allows unit connection to duct-works, both for air suction and discharge.

This series comprises 2 basic models which cover a capacity range from 94 to 124 l/24h.

SHH

Swimming pool dehumidifiers

Series SHH dehumidifier are expressly designed for use in swimming pools where humidity should be closely controlled in order to guarantee optimal comfort. These units are intended to be installed in a technical room close to the swimming pool. A centrifugal fan with high available static pressure allows unit connection to duct-works, both for air suction and discharge.

This series comprises 5 basic models which cover a capacity range from 330 to 937 l/24h. All the units are fully assembled and wired at the factory, carefully evacuated and dried after leak tests under pressure and then charged with refrigerant R407C. They are all fully operational tested before shipment. They all conforms to European Directives and are individually marked with the CE label and provided with Conformity Declaration.

ACCESSORIES Built- in mechanical hygrostat. Remote mechanical hygrostat. Desuperheater: plate type, in molybdenum alloy steel, this device is an additional heat exchanger fitted on the compressor discharge line, in series with the condensing coil. This solution allows to get a heat recovery capacity around 25 % of condensing load, useful to produce hot water for sanitary use or reheat the swimming pool. Hot water coil.

SRH

Swimming pool dehumidifiers

Series SRH dehumidifier are expressly designed for use in swimming pools where humidity should be closely controlled in order to guarantee optimal comfort. These units are intended to be installed in a technical room close to the swimming pool. A centrifugal fan with high available static pressure allows unit connection to duct-works, both for air suction and discharge.

This series comprises 6 basic models which cover a capacity range from 1150 to 3000 l/24h. All the units are fully assembled and wired at the factory, carefully evacuated and dried after leak tests under pressure and then charged with refrigerant R407C. They are all fully operational tested before shipment. They all conforms to European Directives and are individually marked with the CE label and provided with Conformity Declaration.

ACCESSORIES Built- in mechanical hygrostat. Remote mechanical hygrostat. Remote mechanical hygrostat + thermostat. Remote electronic hygrostat + thermostat. Desuperheater: plate type, in molybdenum alloy steel, this device is an additional heat exchanger fitted on the compressor discharge line, in series with the condensing coil. This solution allows to get a heat recovery capacity around 25 % of condensing load, useful to produce hot water for sanitary use or reheat the swimming pool. Hot water coil: finned coil type constructed from copper tubes mechanically expanded into aluminium fins. 3 way On/off valve to be connected to the hot water coil. Fresh air module: supplied with cross flow heat exchanger, painted aluminium fins, exhaust fan and fresh air, EU4 air filter, coupled dampers with servomotor (controlled by the unit microprocessor).

UTH

Swimming pool dehumidifiers

The energy recovery high efficiency dehumidifiers UTH range have been designed to grant the complete control of temperature, humidity, the energy recovery and the fresh air treatment in the covered swimming pools or in other applications with very high internal loads. The UTH units can operate in environments up to 36°C and are able to manage up to 30% of fresh air. The range includes 7 models, which covers airflows range from 1500 to 6000 m3/h. The use of double-passage-cross-flow energy recovery allows to increase up to 20% the dehumidification capacity in comparison to the traditional dehumidifiers. The use of the double passage in the energy recovery, in fact, allows the free sensible pre-cooling of the air near to the saturation point, giving so the possibility to the unit to work, basically, in latent load. All the units are fully assembled and wired at the factory, carefully evacuated and dried after leak tests under pressure and then charged with refrigerant R407C. They are all fully operational tested before shipment. They all conforms to European Directives and are individually marked with the CE label and provided with.

ACCESSORIES: Partial heat recovery It is used to produce hot sanitary water or to heat the swimming pool; it is made of molibdenum alloy AISI 316 stainless steel; plate type. Condensate discharge pump Package centifual type, with high available static pressure, it is supplied with internal water tank, one way valve, floating device. The pump is equipped with a contact alarm who stops the operation of the unit in case of pump defect. Low ambient kit It is used when the ambient temperature is below -5°C; the device allows the correct operation of the unit with very low external temperatures (down to -30°C) keeping the correct working range of the internal components.